Click for more products.
No products were found.
Blog search
Latest Comments

FIBARO HC2 / HCL v 4.590 CHANGELOG

Version 4.590

The possibility of transferring the cloud backup to Home Center 3!
- Use the Transfer Configuration feature available from the Remote Access (home.fibaro.com).
- Both gateways must be assigned to the same Fibaro ID account and available on the Home Center list.
- The backup must be created on version 4.581 or higher.
- Home Center 3 must be on version 5.021 or higher.
- All Z-Wave devices, their configuration, room assignment, associations and parameters will be transferred.
- If you have thermostats, they will await reconfiguration.
- Scenes will not be moved and need to be created again.
- Virtual devices will not be moved. Use a new tool - Quick Apps - to implement them.
- The gateway from which you are moving the backup will still be available, but the devices will no longer communicate at all.
- The migration process cannot be undone - it is irreversible.

 

New improvements:
- Added target and measured temperature chart in General tab of FIBARO Heat Controller (FGT-001) version 4.5 or higher.
- Possibility to disable sending system notifications as push messages.
- Optimized time needed to change setpoint of the heating zone with multiple FIBARO Heat Controllers (FGT-001).
- Support for IP Cameras using Digest authentication.
- Added Warming Prioritizer plugin to bind FIBARO Heat Controller version 4.7 or higher and switch that controls the boiler.
- Added support for MCOHome MH9-CO2-WA and MH9-CO2-WD version 2.4.
- Added support for MCOHome MH10-PM2.5-WA and MH10-PM2.5-WD version 2.3.
- Added support for MCOHome MH7-WB version 4.2.
- Added support for MCOHome A8-9 version 6.2.
- Added support for Aeotec Heavy Duty Switch version 3.28.
- Added support for Sensative Strips Comfort.
- Added support for Sensative Strips Drip.
- Added support for Eurotronics Spirit TRV.
- Added support for Dome Siren (DMS01).
- Added support for Dome Water Main Shut-Off (DMWV1).

 

Resolved issues:
- Synchronization of heating schedules with multiple thermostats overloads the system and results in no interface response.
- Control of other devices during synchronization of heating schedules is not possible or works with a long delay.
- Block scene changing the LED ring illumination of FIBARO Walli series devices ignores set delay.
- Brightness set in FIBARO RGBW 2 (FGRGBW-442) changes automatically after refreshing the page.
- Colour set in FIBARO RGBW 2 (FGRGBW-442) is not the same in different parts of the interface.
- Favourite colour cannot be added for FIBARO RGBW (FGRGBWM-441)
- Restoring backup fails in some cases.
- Incorrect status of FIBARO CO Sensor (FGCD-001) in event panel.
- Scene controller endpoint is hidden for FIBARO Single Switch (FGS-213).
- Redundant updating of schedule during its synchronization in FIBARO Heat Controller (FGT-001).
- Z-Wave devices do not display available firmware updates.
- Energy data is not removed from all endpoints of the device.
- Plugin view is not loaded in the mobile app.
- Incorrect support for Fakro ZWS12 with rain sensor.
- Incorrect support for Forest Shuttle.
- Missing translations in Italian.
- Other minor fixes.

Related products
4 Comments
  • Ra****** ****ec

    Ra****** ****ec 04.11.2020

    Dobrý deň, pozrel som sem a vidím že posledná aktualizácia je na verziu 4.590, ako to že ja mám v HC2 verziu 4.600?
    • Sm********* ****

      Sm********* **** 06.11.2020

      Dobrý deň,
      ďakujeme za dotaz.

      Jednoducho je to preto, lebo neprekladáme každý changelog (zoznam zmien).
      Najnovší originálny changelog aktualizácií pre FIBARO HC2 nájdete - https://forum.fibaro.com/forum/38-home-center-2/

      Pekný deň.
  • Zd***** ***ek

    Zd***** ***ek 02.07.2020

    Dobrý den mám tuto verzi softwaru FIBARO HC2 / HCL V 4.590 v HC2 a musel jsem dát po nějaké době reset.Začali mi zlobit postupně všechny čidla a sceny. Po resetu vše zmizelo, přes Fibaro ID se vzdáleně připojím do jednotky , bohužel nejde nic konfigurovat,přidávat čidla uživatele , asistenta prvního spuštění , prostě nic. Na ID Fibaro jednotku vidím online , pridal jsem tam i usery , ale stále po připojení nemohu nic dělat.Nějakou radu co s tím ? Repair jsem už zkoušel 3x . Děkuji
    • Sm*********

      Sm********* 03.07.2020

      Dobrý deň,
      žiaľ ide o bug v danej verzii firmvéru,kedy časové scény prestanú po určitej dobe fungovať. Ako dočasné riešenie zatiaľ fungoval reštart HC2/HCL. Dôležité je mať spravené zálohy. Ak je po reštarte problém, tak je nutné kontaktovať FIBARO technickú podporu, žiaľ my s tým pomôcť zatiaľ nevieme (nemáme oprávnenia).
      Ďakujeme.
Leave a Comment
Leave a Reply
Please login to post a comment.

Menu

Settings

Create a free account to save loved items.

Sign in

Create a free account to use wishlists.

Sign in