New products

Philio PSP05-C Outdoor Motion Sensor

Philio PSP05-C Outdoor Motion Sensor

59,99 €
49,99 € tax excl.
Philio Dimmer Socket - Gen5 (PHIEPAD02)

Philio Dimmer Socket - Gen5 (PHIEPAD02)

48,90 €
40,75 € tax excl.
Netatmo Smart Thermostat (NTH01-EN-EU)

Netatmo Smart Thermostat (NTH01-EN-EU)

178,80 €
149,00 € tax excl.
Danfoss HC10 Hydronic controller for 10 outputs

Danfoss HC10 Hydronic controller for 10 outputs

289,90 €
241,58 € tax excl.
TKB Thermostat for Floor heating (TZ10.36)

TKB Thermostat for Floor heating (TZ10.36)

70,00 €
58,33 € tax excl.
Raspberry PI 8MP Camera Board V2

Raspberry PI 8MP Camera Board V2

33,00 €
27,50 € tax excl.

Manufacturers

Qubino Flush PWM Thermostat Plus [ZMNHLD1]

GOA_ZMNHLD1-211

New product

Z-Wave Qubino Flush PWM Thermostat Plus module with temperature sensor included for PID heating system control

  • PWM Thermostat Function
  • PID controller
  • Use to directly control a water or electric underfloor heating system, boiler, hot water pump, electric heater, etc
  • Z-Wave Plus Certified

More details

68,28 €


56,90 €  tax excl.
in stock

- +

 
More info

 

New Qubino PWM Thermostat Plus

The Qubino Flush PWM Thermostat module uses PWM (Pulse Width Modulation) to control a heater. The module features a wide range of parameters, including the  P, I and D parameters, PWM cycle duration, maximum and minimum values, and other useful options to regulate the PWM system.

The module will itself control your heating according to the instructions you supply. Based on the temperature measured by the sensor, the module will adjust the functioning of the heating system so that it meets the required temperature.

 

Flush PWM Thermostat Plus

PWM Thermostat Plus with temperature sensor included for PID heating system control

  • PWM Thermostat Function
  • PID controller
  • Integrates a 500 series Z-Wave chip
  • Extended temperature range -50.0°C to +125°C
  • Very low power consumption, less than 0.4W
  • No batteries required - connected to 24V or 230V supply
  • Frost free mode: Specifies a minimum temperature for the heating system connected to the module and prevent your pipes from freezing
  • Includes a temperature sensor with a 1m cable

 

Z-Wave Plus

 

Technical details:

  • Wireless: Z-Wave (868.42MHz)
  • Voltage: 110 - 230 VAC ± 10% 50 / 60Hz, 24 - 30VDC
  • Rated load current of AC output (resistive load): 0.85 X 10A / 230VAC
  • Rated load current of DC output (resistive load): 0.85 X 10A / 30VDC
  • Power circuit AC output (resistive load): 200W (230VAC)
  • Power circuit DC output (resistive load): 21W (24VDC)
  • Power monitoring accuracy: +/-2W
  • Power Consumption: < 0.4W
  • Digital temperature sensor measurement range: -50 ~ 125°C
  • Operating Temperature: -10 to +40°C
  • Range: up to 30m indoors (depending on surrounding material)
  • Dimensions (LxWxH): 41.8 x 36.8 x 15.4mm
  • Weight: 48g
  • Length of temperature sensor cable: 1000 mm
 
Features and compatibility
Z-Wave technologyZ-Wave Plus (Gen 5) 868.42 MHz
IoT - Internet of ThingsWireless communication
Neutral wireRequired
Power SupplyCable Power
Heating ControlElectric floor heating
Type of useIndoor
IP RatingIP20
Temperature MeasurementYes
FIBARO HC2 CompatibilityNot Tested
FIBARO HC LITE CompatibilityNot Tested
VERA PLUS CompatibilityNot Tested
VERA EDGE CompatibilityNot Tested
ZIPABOX CompatibilityNot Tested
RAZBERRY CompatibilityNot Tested
POPP CompatibilityNot Tested
PIPER CompatibilityNot Tested

Write a review

Write a review

Related articles

Tips for installing a wireless system for smart home

Installing some of the Z-Wave system components can sometimes be a challenge. With our tips, you will be ready to...

What is Z-Wave Plus?

What is Z-Wave Plus?

Customers who bought this product also bought:

30 other products in the same category:

Menu

Compare 0