New products

Philio PSP05-C Outdoor Motion Sensor

Philio PSP05-C Outdoor Motion Sensor

59,99 €
49,99 € tax excl.
Philio Dimmer Socket - Gen5 (PHIEPAD02)

Philio Dimmer Socket - Gen5 (PHIEPAD02)

48,90 €
40,75 € tax excl.
Netatmo Smart Thermostat (NTH01-EN-EU)

Netatmo Smart Thermostat (NTH01-EN-EU)

178,80 €
149,00 € tax excl.
Danfoss HC10 Hydronic controller for 10 outputs

Danfoss HC10 Hydronic controller for 10 outputs

289,90 €
241,58 € tax excl.
TKB Thermostat for Floor heating (TZ10.36)

TKB Thermostat for Floor heating (TZ10.36)

70,00 €
58,33 € tax excl.
Raspberry PI 8MP Camera Board V2

Raspberry PI 8MP Camera Board V2

33,00 €
27,50 € tax excl.

Manufacturers

Popp Heating Thermostat

POPE010101-272

New product

Z-Wave Popp Heating Thermostat - a Z-Wave controlled electronic radiator thermostat

  • Now with increased network stability
  • Mounted on wall heating valves and controls them by a motor
  • Ensures that the temperature in the room is kept at the desired level
  • LCD panel
  • Up to 9 setpoint for up to 7 week days
  • Energy saving and frost protection, detection of open windows

More details

67,80 €


56,50 €  tax excl.
in stock

- +

 
More info

Z-Wave Popp Heating Thermostat

popp termostat

This device is a Z-Wave controlled electronic radiator thermostat. It is SDK 4.5, has Explorer Frame Support and increased network stability.

This radiator thermostat is mounted on wall heating valves and controls them by a motor. The device accepts a setpoint that is either set manually using buttons on the device or wirelessly using Z-Wave. Afterwards, the device will regulate the warm water supply to the wall radiator and compare the detected temperature to ensure that the temperature in the room is kept at the desired level. A small LCD panel on the device displays the setpoint temperature on request.

The device has an internal scheduler, that allows to define up to 9 setpoint for up to 7 week days. Once programmed, these setpoints will be activated without any further manual or wireless interaction. Beside setting a desired temperature the device will support special heating schemes, such as energy saving and frost protection and intelligent functions such as detection of open windows or a valve training function to ensure that valves are still operational after longer periods.

Compared with Danfoss "Living Connect" the Popp thermostat will report the room temperature as detected and calculated by the device’s temperature sensor to the Z-Wave gateway.

The living connect can be mounted to valves with standard M30x1.5 connector or RA2000

Technical Details

  • Technology: Z-Wave (868.42MHz)
  • Wireless Range: On average up to 40 m inside buildings
  • Battery Type: 2*AA
  • Explorer Frame Support: Yes
  • SDK: 4.55
  • Device Type: Slave
  • Generic Device Class: Thermostat
  • Specific Device Class: Setpoint Thermostat
  • Routing: No
  • Firmware Version 1.0

 

popp termostat

 
Features and compatibility
Z-Wave technologyZ-Wave (Gen 3) 868.42 MHz
IoT - Internet of ThingsWireless communication
Power SupplyBattery
Heating ControlControl of radiators (TRV)
Type of useIndoor
IP RatingIP20
Temperature MeasurementYes
Valve Connector TypeM30x1,5
FIBARO HC2 CompatibilityYes
FIBARO HC LITE CompatibilityYes
VERA PLUS CompatibilityYes
VERA EDGE CompatibilityYes
ZIPABOX CompatibilityNot Tested
RAZBERRY CompatibilityYes
POPP CompatibilityYes
PIPER CompatibilityNo

Write a review

Write a review

Accessories

Customers who bought this product also bought:

30 other products in the same category:

Menu

Compare 0