New products

FIBARO Radiator Thermostat Starter Pack

FIBARO Radiator Thermostat Starter Pack

89,99 €
74,99 € tax excl.
FIBARO Radiator Thermostat Head

FIBARO Radiator Thermostat Head

79,99 €
66,66 € tax excl.
FIBARO Radiator Thermostat Sensor

FIBARO Radiator Thermostat Sensor

19,99 €
16,66 € tax excl.
POPP KeyPad

POPP KeyPad

179,99 €
149,99 € tax excl.
Vera Secure

Vera Secure

299,00 €
249,17 € tax excl.
DIN Rail mounting for 3x Fibaro Modules

DIN Rail mounting for 3x Fibaro Modules

13,99 €
11,66 € tax excl.
DIN Rail mounting for 2x Fibaro Modules

DIN Rail mounting for 2x Fibaro Modules

9,98 €
8,32 € tax excl.
DoorBird Video Door Station D202

DoorBird Video Door Station D202

554,00 €
461,67 € tax excl.

Manufacturers

Z-Wave.me Z-Uno Gen5

ZMEEZUNO-271

New product

Z-Wave.me Z-Uno  is the first and only easy to use developer board that allows you to create your own Z-Wave device

  • The perfect companion for you RaZberry gateway
  • Compatible with other controllers like Fibaro Home Center 2, Fibaro Home Center Lite, Vera Edge and Zipato Zipabox
  • Control any Arduino compatible peripherals
  • Z-Wave Plus Certified
  • For developers only

More details

59,40 €


49,50 €  tax excl.
in stock

- +

 
More info

Z-Uno is the first and only easy to use developer board that allows you to create your own Z-Wave device without deep knowledge of Z-Wave protocol or programming. Z-Uno is a mix of Z-Wave home automation radio protocol power and Arduino simplicity. Being inspired by Arduino project Z-Uno inherits all concepts of easy-to-use hardware and software solutions, keeping maximum flexibility.

Z-Uno is a fully DIY product. It is made for those who are limited by existing choice of Z-Wave products and wants to extend their smart homes with more sensors and actuators: connect LEDs, buttons, switches, motors or any low voltage sensor including most of Arduino compatible sensors.

Z-Uno programming is done by writing sketch in simplified C language and loaded into Z-Uno using Arduino IDE. Many examples and comprehensive tutorials will help you to make your own project.

Being Z-Wave Plus certified device, Z-Uno is the perfect companion for you RaZberry gateway. Z-Uno is compatible with other controllers too: among them Fibaro Home Center 2, Fibaro Home CenterLite, Vera Edge and Zipato Zipabox.

Make your own Z-Wave device:

  • Control any Arduino compatible peripherals
  • Define your own logic by modifying your sketch
  • Use Arduino IDE and language to write and upload sketches
  • Easy to use
  • Requires no knowledge of Z-Wave protocol
  • Complete DIY solution

z-uno

Technical Data

Hardware specification

  • 28 kB Flash memory for your sketches
  • 2 kB RAM available
  • Z-Wave RF transmitter at 9.6/40/100 kbps
  • 26 GPIO (overlaps with special hardware controllers)
  • 4 ADC
  • 5 PWM
  • 2 UART
  • 1 USB (serial port)
  • 1 SPI (master or slave)
  • 1 Interrupt
  • 2 service LED, 1 service button
  • 1 user test LED

Dimensions

  • L×W×H: 39×20×16 mm (PCB dimensions with all components)
  • L×W×H: 39×20×7 mm (PCB dimensions with PLS and battery connectors removed)
  • Antenna lenght: 86 mm (89 mm with isolation), can be bent to better fit your dimensions
  • Weigth: 7 g
  • Antenna type: wire antenna 86 mm for 865-870 MhZ
  • Alternative antenna: optional u.fl connector can be soldered (to RF2 pads)

Power modes

  • USB 5 V, external 5 or 3 V, external 7-18 V or battery (via MU-2F connector, included)
  • always on, sleeping or FLiRS (Frequently Listening) 

 

Z-Wave supported features

  • Z-Wave Plus compliant
  • All Z-Wave frequencies (check availability)
  • Out of the box support of AES 128 bit Security
  • Upgrade via USB or radio (Z-Wave OTA)
  • Multichannel (10 channels)
  • 5 Association groups
  • Controls switches, dimmers, door locks(future feature) and scenes
  • Works with gateways and/or directly with other Z-Wave devices
  • Channel types: Binary Switch; Multilevel Switch; Colour Switch; Binary Sensor; Multilevel Sensor

Electrical characteristics

  • Digital pin in logical 1: > 2.1 V, leakage current 10 μA
  • Digital pin in logical 0: < 0.9 V, leakage current 10 μA or 40-120 μA (with internal pull-up enabled)
  • Internal pullup resistor: 15-20 kΩ (at +25°C)
  • Digital pin out logical 1: > 2.4 V, max current sourcing 8 mA (16 mA for digital pins 3-6)
  • Digital pin out logical 0: < 0.4 V, max current sinking 8 mA (16 mA for digital pins 3-6)
  • Total max current sourcing from GPIO pins: 120 mA
  • Power consumption on 3.3 V: in always listening mode 50 mA, in sleep mode 1 mA (about 7 μA if one DC-DC is unsoldered), in FLiRS mode 1 mA (about 70 μA if one DC-DC is unsoldered)

 

 

 

 
Features and compatibility
Z-Wave technologyZ-Wave Plus (Gen 5) 868.42 MHz
IoT - Internet of ThingsWireless communication
Type of useIndoor
IP RatingIP20
FIBARO HC2 CompatibilityYes
FIBARO HC LITE CompatibilityYes
VERA PLUS CompatibilityPartial
VERA EDGE CompatibilityPartial
ZIPABOX CompatibilityYes
RAZBERRY CompatibilityYes
POPP CompatibilityYes
PIPER CompatibilityNot Tested
Notes to compatibilityVera controllers - not all types of sensors are supported

Write a review

Z-Wave.me Z-Uno Gen5

Z-Wave.me Z-Uno  is the first and only easy to use developer board that allows you to create your own Z-Wave device

  • The perfect companion for you RaZberry gateway
  • Compatible with other controllers like Fibaro Home Center 2, Fibaro Home Center Lite, Vera Edge and Zipato Zipabox
  • Control any Arduino compatible peripherals
  • Z-Wave Plus Certified
  • For developers only

Write a review

Related articles

Raspberry Pi 3 and Smarthome

Using Z-Wave with Raspberry Pi 3

Customers who bought this product also bought:

6 other products in the same category:

Menu

Compare 0