New products

Philio PSP05-C Outdoor Motion Sensor

Philio PSP05-C Outdoor Motion Sensor

59,99 €
49,99 € tax excl.
Philio Dimmer Socket - Gen5 (PHIEPAD02)

Philio Dimmer Socket - Gen5 (PHIEPAD02)

48,90 €
40,75 € tax excl.
Netatmo Smart Thermostat (NTH01-EN-EU)

Netatmo Smart Thermostat (NTH01-EN-EU)

178,80 €
149,00 € tax excl.
Danfoss HC10 Hydronic controller for 10 outputs

Danfoss HC10 Hydronic controller for 10 outputs

289,90 €
241,58 € tax excl.
TKB Thermostat for Floor heating (TZ10.36)

TKB Thermostat for Floor heating (TZ10.36)

70,00 €
58,33 € tax excl.
Raspberry PI 8MP Camera Board V2

Raspberry PI 8MP Camera Board V2

33,00 €
27,50 € tax excl.

Manufacturers

Danfoss Z-Wave Room Sensor

DAN_RS-Z-182

New product

  • Can be controlled by any Z-Wave controller (e.g. Fibaro, Vera, ...)

  • 868.4 MHz radio frequency - for use in whole EU

  • Include in a Z-Wave network to measure temperature

  • Set-point override function

  • Additional button for custom function

More details

92,99 €


77,49 €  tax excl.
backorder

- +

 
More info

 

This Z-Wave device is used as a central temperature sensor for heating or cooling solutions with multiple actuators. The measured temperature is displayed. Two buttons allow to override the set-point temperature. It can be used as Z-Wave stand alone temperature sensor or to control heating, cooling of ventilation devices. The override can be terminated after a certain time. After this time the set-point temperature will go back to the defined value. Beside the two front buttons the device has one more button on the top side. The use of this button will be defined by the central controller. Possible functions can include a temperature boost (heat up as soon as possible) or the activation of a energy saving mode. 

 

 

Technical details:

  • Temperature sensor measurement range: 0‒40°C
  • Item dimensions: 81.0 x 66.0 x 21.0mm
  • Item weight: 116g
  • Battery power: 2 x AA (included)
  • Battery lifetime: Up to 4-5 years
  • IP rating: 21
  • Range: up to 30m
  • Transmission power: max. 1mW
  • Transmission frequency: 868.42MHz
  • Backlight: green LED
  • Battery monitoring: built-in monitoring circuit - detecting low or critical battery level

                                   

What's in the box?

  • Temperature Sensor
  • Installation Guide
  • 2 x Wall Screws
  • 2 x Wall Plugs
 
Features and compatibility
Z-Wave technologyZ-Wave (Gen 3) 868.42 MHz
IoT - Internet of ThingsWireless communication
Power SupplyBattery
Heating ControlSingle wireless thermostat
Type of useIndoor
IP RatingIP21
Temperature MeasurementYes
FIBARO HC2 CompatibilityYes
FIBARO HC LITE CompatibilityYes
VERA PLUS CompatibilityNot Tested
VERA EDGE CompatibilityNot Tested
ZIPABOX CompatibilityYes
RAZBERRY CompatibilityYes
POPP CompatibilityYes
PIPER CompatibilityNot Tested

Write a review

Danfoss Z-Wave Room Sensor
  • Can be controlled by any Z-Wave controller (e.g. Fibaro, Vera, ...)

  • 868.4 MHz radio frequency - for use in whole EU

  • Include in a Z-Wave network to measure temperature

  • Set-point override function

  • Additional button for custom function

Write a review

Related articles

LUA: Danfoss RS – Thermostat

LUA script for Fibaro HC2. Use the Danfoss Z-Wave room sensor as a thermostat and set the temperature in the...

Customers who bought this product also bought:

30 other products in the same category:

Menu

Compare 0